Faucet Repair
Faucet repair el paso TX done right the first time
When a faucet drips, you feel it in your water bill and hear it at 2 a.m. Our faucet repair el paso TX service stops the leak at the source, not just the symptom. We fix kitchen and bathroom fixtures across El Paso County, from Moen and Kohler cartridges to corroded supply lines. Same-day appointments, upfront pricing, and a warranty on every repair.
Service overview
What faucet repair el paso TX actually involves
Faucet repair el paso TX is the licensed diagnosis and correction of leaks, drips, and flow failures in kitchen and bathroom fixtures. It covers worn cartridges, failed O-rings, cracked valve seats, corroded supply lines, and mineral-clogged aerators. We pull the faucet apart, inspect the valve body, and replace only the failed components with OEM parts from Moen, Kohler, or American Standard. Most single-handle repairs take 45 to 90 minutes. If the valve seat is scored or the body is cracked, we quote a full replacement instead of charging you for a repair that will not hold.
El Paso's hard water is brutal on faucets. The calcium and magnesium in our municipal supply builds scale inside cartridges and aerators, which is why so many local fixtures start dripping within two to three years of installation. We see it constantly in older homes around Sunset Heights and Manhattan Heights, where original brass fixtures have been rebuilt three or four times. If you are searching for faucet fixing near me in el paso for dripping faucets, the fix is usually a cartridge swap and a good descaling, not a whole new faucet. We also check your shutoff valves while we are under the sink, because a seized angle stop turns a simple repair into a flooded cabinet.
Practical benefits
Why El Paso homeowners call us first
A dripping faucet wastes water, stains the sink, and gets worse every month. Here is what you get when you book our team.
Stop the water waste
A faucet dripping once per second wastes more than 3,000 gallons a year. We replace the failed cartridge or seat, test the handle through 20 full on-off cycles, and confirm zero drips before we pack up. Your next water bill reflects the fix.
Hard water specialists
El Paso water runs 8 to 12 grains per gallon of hardness. That scale chews through rubber seals and ceramic cartridges. We descale the valve body, install new seals rated for hard water, and can add a water softener quote if you are tired of replacing fixtures every couple of years.
Same-day and 24/7
We keep Moen, Kohler, and American Standard cartridges on every truck, so most repairs finish in one visit. For burst supply lines or a faucet that will not shut off, our faucet fixing el paso 24/7 line dispatches a licensed plumber any hour, including weekends and holidays.
Upfront pricing, no surprises
You get the price before we start. Standard cartridge and seal repairs fall in a predictable range, and we tell you on the phone if the job sounds like a replacement instead. No diagnostic fee when you approve the repair, and every fix carries a written warranty.
How service works
How our faucet repair process works
From your first call to the final drip test, here is exactly what happens when you book faucet repair in el paso, Texas with our team.
STEP 01
Phone diagnosis
You describe the drip, the handle feel, and the fixture brand. We ask whether the leak is at the spout, the base, or under the sink, because each points to a different failed part. Most calls take five minutes, and we give you a price range before we roll a truck.
Tools and methods
Tools and methods we use
Pipe wrench
Used to hold the valve body and loosen supply line nuts without twisting the faucet. We size the wrench to the fitting so we do not scar chrome or crack plastic valve housings.
Leak detection equipment
When a drip is not coming from the faucet, we use leak detection equipment to trace hidden leaks in walls and cabinets. That keeps us from replacing a good faucet when the real problem is a pinhole in a supply pipe.
Propane torch
For copper supply line repairs behind the wall, we solder fittings with a propane torch. We use a heat shield to protect the cabinet and countertop, and we pressure-test the joint before closing up.
Tube bender
Bends copper and PEX tubing to route new supply lines without kinks. Clean bends mean better flow and fewer stress points that crack over time in El Paso's hard water.
Press tool
For copper and PEX connections where soldering is not safe near finished surfaces. The press tool makes a permanent crimp fitting in seconds, and we verify each joint with a pressure test.
Sewer camera
If a faucet repair reveals a slow drain or gurgling, we run a sewer camera to check the line. It shows root intrusion or a collapsed section before it backs up into your kitchen.
OEM cartridge replacement
We match the cartridge to the faucet brand, Moen, Kohler, or American Standard, and install the genuine part. Aftermarket cartridges often fail within a year in hard water, so we stick with OEM and warranty the work.
Hard water descaling
We soak and scrub the valve body and aerator to remove calcium and magnesium scale. Descaling restores smooth handle travel and full flow, and it slows the next round of buildup so the repair lasts longer.
Pressure and flow testing
After every repair, we test static pressure at a nearby hose bib and check flow at the fixture. If pressure is above 80 psi, we recommend a pressure-reducing valve to protect cartridges and supply lines across the house.
Uniform Plumbing Code compliance
Every connection we touch follows the Uniform Plumbing Code (UPC), from supply line sizing to shutoff placement. That keeps your repair legal, insurable, and consistent with what a home inspector will look for later.
Where this service fits
When to book faucet repair
Your kitchen faucet drips every few seconds and the water bill jumped $20 last month.
We replace the cartridge and seals, descale the valve body, and test the spout for drips. The whole job usually takes under 90 minutes, and we check the disposal and drain while we are under the sink. The drip stops, your water bill drops back to normal, and the handle feels smooth again. Most customers see the difference on the very next billing cycle.
You wake up to water on the bathroom floor and the faucet base is soaked.
We treat it as an emergency, shut off the supply, and replace the base O-ring, mounting gasket, and any brittle supply lines. We dry the cabinet, check for water damage, and test the fixture for 10 minutes before leaving. The floor stays dry, the cabinet is saved from rot, and the faucet is sealed and stable. You get a written warranty on the repair.
Your older home in Manhattan Heights has original brass faucets that have been rebuilt three times.
We inspect the valve seats and body for scoring. If a rebuild will hold, we install hard-water-rated cartridges and seals. If the body is cracked, we quote a Moen or Kohler replacement that matches the sink. You either get a rebuild that lasts years or a clean new fixture that fits the existing countertop. Either way, you stop paying for the same repair every 18 months.
A guest bathroom faucet has not been used in months and now leaks when you turn it on.
Sitting water dries out seals and lets scale harden in the cartridge. We replace the dried seals, flush the line, and test hot and cold flow. We also check the shutoff valves, which often seize on unused fixtures. The guest bathroom is ready for visitors, with no drips and no surprise leaks. The repair is warrantied, so you are covered if the fixture sits unused again.
Local execution
How faucet repair runs in El Paso
El Paso's water is the number one reason faucets fail here. At 8 to 12 grains per gallon of hardness, the calcium and magnesium in our supply chew through rubber seals and ceramic cartridges faster than in softer-water cities. Add summer temperatures that push 100 degrees and winter nights that dip below freezing, and you get fixtures that expand, contract, and scale up year after year. Older neighborhoods like Sunset Heights and Manhattan Heights still have original brass faucets and galvanized supply lines, while newer builds on the Eastside and Pebble Hills use PEX and modern valve platforms. We work with both. Our plumbers follow the Uniform Plumbing Code (UPC) and pull permits when the job requires it, and we keep OEM parts for Moen, Kohler, and American Standard on every truck. If you need faucet fixing el paso 24/7, we dispatch around the clock, including holidays. And if hard water keeps killing your fixtures, we will quote a water softener so you stop paying for the same repair every two years.
Sunset Heights
Historic homes here often have original brass faucets and galvanized supply lines. We rebuild them with hard-water-rated parts and check the shutoffs, which seize more often in older plumbing.
Eastside
Newer construction with PEX supply lines and modern Moen or Kohler fixtures. Repairs are usually straightforward cartridge swaps, and we check the pressure-reducing valve while we are there.
Lower Valley
Some homes here still run on well water, which is even harder than city supply. We descale aggressively and recommend filtration or softening to protect every faucet in the house.
Kern Place
A mix of renovated and original homes. We see a lot of kitchen faucet repairs here after remodels, when new fixtures meet old supply lines and angle stops that need replacing.
Hard water at 8-12 grains per gallon
Scale builds inside cartridges and aerators, causing drips and low flow within two to three years. We descale every repair and install hard-water-rated seals to extend the life of the fixture.
Summer heat above 100 degrees
Heat expands metal supply lines and stresses fittings. We check for weeping at connections during summer repairs and replace any brittle supply lines before they burst.
Winter overnight freezes
Freezing nights can crack exposed pipes and supply lines, which then leak when they thaw. We inspect outdoor and garage lines during winter calls and insulate where needed.
Older galvanized plumbing in central neighborhoods
Galvanized pipes corrode from the inside, dropping pressure and sending rust debris into faucet cartridges. We flush the lines and recommend repiping when corrosion is advanced.
Problems we solve
Faucet problems we fix in El Paso
Most faucet calls come down to five failures. Here is what we see every week and how we solve each one for good.
Faucet drips constantly, even when shut off
We replace the cartridge, springs, and O-rings with OEM parts, descale the valve seat, and test the handle through 20 on-off cycles. Most drips stop the same visit, and the repair carries a written warranty on parts and labor. A steady drip wastes thousands of gallons a year, stains the sink basin, and can overflow if the drain is slow. It also signals a worn cartridge that will eventually fail completely.
Water pools at the base of the faucet
We pull the faucet, replace the base O-ring and mounting gasket, reseal the deck, and tighten the mounting hardware to spec. Then we dry the area and run water for five minutes to confirm the leak is gone. Water seeping around the base means a failed O-ring or a loose mounting nut. Left alone, it rots the countertop and grows mold inside the cabinet within weeks.
Low water pressure from hard water scale
We remove and descale the aerator, flush the cartridge, and check the supply lines for debris. If scale is heavy, we recommend a water softener to protect every faucet in the house, not just the one that clogged. Scale builds inside the aerator and cartridge, cutting flow to a trickle. Dishwashing and handwashing take longer, and the restricted flow puts extra strain on the fixture.
Handle is stiff or will not turn
We disassemble the valve, clean out the scale, and install a new cartridge with food-grade silicone grease on the moving parts. The handle turns smoothly again, and we test full hot-to-cold travel before we finish. A stiff handle usually means a failing cartridge or mineral buildup in the valve body. Forcing it can crack the cartridge housing and turn a simple repair into a full faucet replacement.
A practical standard for every visit.
Clear planningPrepared arrivalsCareful workLocal follow-through
Experience in the details
Licensed faucet repair expertise you can verify
Our plumbers hold Texas State Board of Plumbing Examiners (TSBPE) licenses and work under a Master Plumber who has rebuilt thousands of fixtures across El Paso County. We train on current Moen, Kohler, and American Standard valve platforms, and we follow the Uniform Plumbing Code (UPC) on every repair. That means correct shutoff placement, proper supply line sizing, and no crossed connections. We also carry leak detection equipment and a sewer camera on every truck, because a faucet problem sometimes points to a bigger pressure or drainage issue.
- TSBPE-licensed plumbers working under an active Master Plumber license
- OEM cartridge and seal inventory for Moen, Kohler, and American Standard fixtures
- Hard water descaling protocol built for El Paso's 8-12 grain water
- Supply line and angle stop inspection included with every faucet repair
- Uniform Plumbing Code (UPC) compliance on every connection we touch
Where we work
One local team. A lot of ground covered.
Downtown El PasoSunset HeightsManhattan HeightsKern PlaceFive PointsEastsideNortheast El PasoWestsideCentral El PasoLower ValleyHorizon CityMontwood
Check my address Notes from local customers
What El Paso customers say
Our kitchen faucet had dripped for months and the handle was stiff. The plumber showed up on time, pulled the Moen cartridge, and showed me the hard water scale inside. He swapped the cartridge and seals, tested it 20 times, and the drip was gone in under an hour. Price was exactly what he quoted on the phone.
A supply line under the bathroom sink let go at 11 p.m. and water was everywhere. I called the 24/7 line and a licensed plumber was at the house in about 75 minutes. He replaced both angle stops and the supply lines, checked the faucet, and cleaned up the cabinet. No more leaks.
Two faucets in our older house kept dripping because of the hard water. The tech rebuilt both with new cartridges, descaled the valve bodies, and recommended a water softener. Six months later, still no drips. He also noticed a slow drain and cleared it while he was there. Fair price, no upsell.
Most faucet repairs in El Paso run $150 to $350 in 2026, including parts and labor. A standard cartridge and seal replacement on a kitchen faucet usually lands near the lower end. Costs rise if the valve seat is scored, the supply lines need replacing, or the faucet is a specialty brand. We give you a firm price before we start, and there is no diagnostic fee when you approve the repair.
We do. Our licensed plumbers cover every El Paso neighborhood, from Downtown and Sunset Heights to the Eastside, Westside, and Lower Valley. We stock Moen, Kohler, and American Standard cartridges on every truck, so most faucet fixing jobs finish in one visit. Call +1 (915) 285-0728 and we will confirm a same-day or next-day window.
Yes. A dripping faucet is almost always a worn cartridge, a failed O-ring, or a mineral-clogged valve seat, and all three are repairable. We pull the faucet apart, replace the failed parts with OEM components, descale the valve body, and test the handle through 20 on-off cycles. Most drips stop the same day, and the repair carries a written warranty.
It is worth repairing when the valve body is solid and the fixture is a quality brand like Moen, Kohler, or American Standard. A $200 repair beats a $450 replacement, especially if the faucet matches your sink and countertop. We inspect the body first and tell you honestly if a rebuild will hold. If the seat is scored or the body is cracked, we quote replacement instead.
Keep exploring
Related Services
Your next step is waiting
Book faucet repair el paso TX today
Stop the drip before it stains your sink or spikes your water bill. Our licensed plumbers carry the parts to finish most repairs in one visit, and every job carries a written warranty. Call now and we will confirm a same-day window or dispatch our 24/7 emergency line.
Start with the basics
Contact plumbing in el paso
Call us at +19152850728 any time, day or night. For non-emergency work, we schedule Monday through Friday and offer Saturday appointments. You get a real arrival window and a text when the tech is on the way. Email works too if you prefer to send photos of the problem first.